Before you can configure your APM, you will need to first connect everything together. This guide will show you all the cables and parts that you will need to connect to your APM.
Typical Quadcopter Layout
Please note the illustration Below highlights a (TYPICAL) installation. It contains optional equipment including a Camera Gimbal and a Battery Monitor and it utilizes an ESC wired “Y” power connection rather than the power distribution board common to many MultiCopters.
1. Connecting your motors and RC gear
Overview of connections on the Ardupilot Mega v2 board
Note: the instructions below are for regular RC receivers with PWM output (one cable per channel). If you’re using a “PPM” receiver (one cable carries all channels), follow the instructions .
Before you can configure your Arducopter, you will need to first connect everything together. This is quite easy. You need to connect your RC receiver to the Input side of the board. You can use the cables included with your Arducopter Kit, or if you are using another frame, you can use jumper cables, or female to female servo cables
Connections between RC receiver and Ardupilot Mega v2 board
If you are using female to female servo cables, the ground (black) side of each connector must be on the outside for the board, the signal (white/orange) needs to be on the inside as shown below.
Connecting with straight connectors
Connecting with right angle connectors
If you are using a multi-pin connector that was included with your Arducopter Kit, connect them as shown below
Input Side for RC reciever
Output side to PDB
Please note, that your ESC, connectors should be plugged in the the output side, it is suggested that you only use power from one of your ESC’s. This can be dune by cutting the red wire on all but one of the ESC’s, or by using a special adaptor. 2. Connecting ArduCopter motors
Once again if you are using an Arducopter Kit, with the PDB, then you dont need to worry about this if you soldered everything correctly as the motors are assigned to the correct pins with the cables you plugged connected in the previous step. However you will neet to make sure your motors are spinning in the correct direction. The images below show the possible arducopter configurations with correct motor orientation
Quick Tip: If your motor is not spinning in the correct direction, simply switch the position of any two of the ESC-motor wires.
Arducopter Hexa, Octa, and Y6
Arducopter OCTA QUAD (X8)
Connecting a Roll-Tilt Camera mount
3. Connecting Optional Sensors
Sonar – Ultrasonic Rangefinder
AC2 supports the MaxSonar line of sonars for low level altitude hold and in the future collision avoidance. Below 10 meters sonar is primarily used for altitude hold. Above 10 meters, the barometric sensor is used. GPS is not required for altitude hold.
Connect your Ultrasonic Sensor to the A0 port of your Ardupilot Mega v2 board
The sonar sensors are quite sensitive to noise, adding something like a ferrite choke to your cable could help. The most important is to mount your sonar away from other electronics like ESC, or wireless telemetry modules.
Possible Causes of sonar Interferance
Electrical noise caused by ESCs, Servos, or switching BEC’s on the same circuit as the Sonar
EMF radiation from motors, motor wires, ESC’s or Xbee.
Acoustic noise from propellers
Vibration from motors, props, etc.
Optical Flow Sensor
The optical flow sensor is used to improve the position hold accuracy of your arducopter. This sensor is supported from Arducopter 2.6 and above.
Connecting the optical flow sensor to APMv2
Power, GND, NCS pins should be attached to A3
MISO, MOSI and SCLK pins should be directly soldered to the pins shown above
Default mounting is lens pointing down, pins forward
Its a good idea to secure the wires with some cable ties so they dont break off over time
How to connect the optical flow sensor to your ardupilot mega board. Make sure the pins are facing forward
Now that everything has been connected everything the next thing to do is configure arducopter firmware for your frame.
|Buyer||Real customer reviews|
17 Jul 2018 02:09
28 Jun 2018 03:06
спасибо. хороший отзывчивый и внимательный продавец. помог с выбором пульта к дрону. очень быстрая доставка. рекомендую.
Leave a Review
We are proud to offer international shipping services that currently operate in over 200 countries and islands world wide. Nothing means more to us than bringing our customers great value and service. We will continue to grow to meet the needs of all our customers, delivering a service beyond all expectation anywhere in the world.
Packages from our warehouse in China will be shipped by ePacket or EMS depending on the weight and size of the product. Packages shipped from our US warehouse are shipped through USPS.
Yes. We provide free shipping to over 200 countries around the world. However, there are some locations we are unable to ship to. If you happen to be located in one of those countries we will contact you.
We are not responsible for any custom fees once the items have shipped. By purchasing our products, you consent that one or more packages may be shipped to you and may get custom fees when they arrive to your country.
|Location||*Estimated Shipping Time|
|United States||10-20 Business days|
|Canada, Europe||10-20 Business days|
|Australia, New Zealand||10-30 Business days|
|Central & South America||15-30 Business days|
|Asia||10-20 Business days|
|Africa||15-45 Business days|
Yes, you will receive an email once your order ships that contains your tracking information. If you haven’t received tracking info within 5 days, please contact us.
For some shipping companies, it takes 2-5 business days for the tracking information to update on the system. If your order was placed more than 5 business days ago and there is still no information on your tracking number, please contact us.
For logistical reasons, items in the same purchase will sometimes be sent in separate packages, even if you've specified combined shipping.
If you have any other questions, please contact us and we will do our best to help you out.
All orders can be cancelled until they are shipped. If your order has been paid and you need to make a change or cancel an order, you must contact us within 12 hours. Once the packaging and shipping process has started, it can no longer be cancelled.
Your satisfaction is our #1 priority. Therefore, if you’d like a refund you can request one no matter the reason.
If you did not receive the product within the guaranteed time( 45 days not including 2-5 day processing) you can request a refund or a reshipment.
If you received the wrong item you can request a refund or a reshipment.
If you do not want the product you’ve received you may request a refund but you must return the item at your expense and the item must be unused.
*You can submit refund requests within 15 days after the guaranteed period for delivery (45 days) has expired. You can do it by sending a message on Contact Us page
If you are approved for a refund, then your refund will be processed, and a credit will automatically be applied to your credit card or original method of payment, within 14 days.
If for any reason you would like to exchange your product, perhaps for a different size in clothing. You must contact us first and we will guide you through the steps.
Please do not send your purchase back to us unless we authorise you to do so.